Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterCopperfield Chimney Cap & Crown in Bethlehem: What to Know First
We provide independent Copperfield chimney cap and crown service in Bethlehem, from cap installation on new flues to crown coating on weather-beaten stacks. Most Copperfield jobs we book are completed in a single visit, with upfront pricing agreed before we start. We’re not the cheapest outfit in the Lehigh Valley, and we don’t try to be. We’re the ones who show up when we say, show you photos of what we found, and fix only what needs fixing. If it needs doing, we’ll tell you. If it doesn’t, we’ll tell you that too. Call (610) 595-5754 for a free estimate.
How Copperfield Products Fail - and How We Fix Them
- Copperfield Multi-Flue Galvanized Caps in Fountain Hill and South Side Bethlehem - The 304-grade mesh on older Multi-Flue units can rust through at the welds after 12 to 15 winters of Lehigh Valley freeze-thaw, especially where road salt spray drifts off Route 378. Homeowners notice brown streaks on the brick below the cap, or birds nesting where the mesh detached. We replace with a Copperfield-compatible stainless cap or a Gelco equivalent, re-flashed to the flue with proper slope so water runs off, not in.
- Copperfield Single-Flue Draft King Caps on West Bethlehem colonials - The Draft King’s wind-driven turbine can seize after years of Bethlehem’s pollen-heavy springs and leaf-fall autumns, sticking open in a storm or closed when you need draft. We disassemble, clean the bearing housing, and if the turbine housing is cracked, we source OEM Copperfield parts or match a compatible Famco unit with the same CFM rating. No guesswork on draft performance.
- Copperfield Chimney Crown on pre-1980s homes near the historic district - Many Bethlehem crowns were poured with too little Portland cement and no reinforcement mesh, and Copperfield’s crown coating can’t bond to crumbly substrate. We sound-test with a hammer, remove loose material to solid concrete, then apply Copperfield CrownCoat or a HeatShield-compatible slurry, depending on crack width and freeze exposure. A coating over bad concrete is money thrown away, so we don’t do it.
- Copperfield Band-Around-Brick caps on twin-flue homes in Hanover Township - The tension band loosens as the chimney course expands and contracts through Bethlehem’s 90-degree summer-to-winter swing. The cap tilts, gaps open, and rainwater hits the flue directly. We re-seat with a stainless band, add copper or stainless counter-flashing where the original mason left none, and caulk with a high-temp sealant rated for Pennsylvania temperature swings.
- Copperfield Outside Mount Caps on oversized flues in Saucon Valley - The expanded metal base can sag on flues wider than 16 inches if the original installer skipped the interior support brackets. We see this where a previous owner upsized to a fireplace insert without upsizing the cap. We install proper Copperfield bracketry or fabricate a custom support from stainless angle stock, then re-mount the cap with correct overhang so water sheds clear of the brick.
Our Copperfield Chimney Cap & Crown Process
- 1
Call and schedule. A live person answers, 24 hours a day. We ask about your chimney age, the Copperfield product name if you know it, and what you’re seeing. We book a window and confirm by text.
- 2
Level-2 camera inspection. Our tech arrives in uniform, background-checked, and photographs the cap, crown, and flue interior. You see the images on a tablet while we explain what we found. No jargon, no pressure.
- 3
Parts decision. If your Copperfield cap is repairable with OEM parts, we say so. If it’s discontinued or the OEM lead time is unreasonable, we quote a quality aftermarket equivalent from Gelco or Famco with the same specs. You choose.
- 4
The repair. Most cap replacements and crown coatings finish in one visit. We work from roof ladders, not by stomping your shingles. Drop cloths on the ground, vacuum after.
- 5
Test and document. We run a smoke test or draft gauge check to confirm the cap draws correctly. Photos of the completed work go to you by email with the invoice.
- 6
The 90-Day Done Right Promise. In writing. If anything’s not right, we come back. No paperwork, no arguing.
What Copperfield Chimney Cap & Crown Costs in Bethlehem
These are real ranges for what we charge in the Bethlehem market, based on 2024-2025 jobs:
| Copperfield single-flue cap replacement (standard size) | $280 - $420 |
| Copperfield multi-flue cap replacement | $450 - $680 |
| Custom fabricated cap for oversized or irregular flue | $550 - $890 |
| Crown repair with Copperfield CrownCoat (minor cracks, sound substrate) | $340 - $520 |
| Crown rebuild plus coating (crumbling concrete, reinforcement needed) | $780 - $1,400 |
| Flashing repair or replacement with cap work | $180 - $350 additional |
What moves the price: accessibility (steep roof, height, landscaping in the way), whether the flue needs cleaning before cap work, and if we find hidden crown damage once the old cap is off. We quote the full number before starting. The number on the estimate is the number on the invoice. Call (610) 595-5754 for an exact quote. Estimates are free.
Why Bethlehem Homeowners Call Hearthstone Chimney Co. for Copperfield Work
We’ve been answering the phone with a live person for over 42 years, and we plan to be here in thirty more. That changes how you treat a customer. Our 90-Day Done Right Promise is in writing, no arguing. Russell Haines and our crew know Copperfield products from two decades of hands-on work, and when a Copperfield part is back-ordered or discontinued, we have relationships with DuraFlex, HeatShield, and Gelco to source equivalent professional-grade materials without leaving you hanging. Background-checked, uniformed technicians. Most jobs in a single visit. Photos you can see, a plain-English verdict. Done right, and we stand behind it.
FAQs
Copperfield’s warranty on the original product expired with normal wear; installing a compatible aftermarket cap does not affect any remaining structural warranty on your flue liner or chimney. As an independent Copperfield service provider, we document the parts we use and their specs so you have a record. Call (610) 595-5754 if you’d like us to review what’s still covered.
We source OEM Copperfield parts when they’re available and the timeline works for the homeowner. When Copperfield has discontinued a line or the lead time stretches past burning season, we match a quality aftermarket cap from Gelco or Famco with identical dimensions, mesh gauge, and CFM rating. We explain both options and the price difference before you decide.
We tap-test the crown with a hammer and inspect with a camera. If the concrete sounds solid and cracks are hairline, Copperfield CrownCoat or HeatShield slurry is appropriate. If the surface crumbles, spalls, or we see rust staining from dissolved reinforcing wire, the crown needs rebuild before any coating goes on. We show you the photos and explain which category you’re in.
A quality stainless or copper cap lasts 15 to 25 years in Bethlehem’s climate. Galvanized steel caps, common on older Copperfield installs, often need replacement at 10 to 15 years due to rust at the welds. If you’re seeing water in the firebox, rust streaks on the brick, or the mesh is pulling away, it’s time for us to look.
Water enters the flue, freezes in the mortar joints, and opens cracks that let carbon monoxide leak or chimney fires spread to the framing. In Bethlehem’s freeze-thaw climate, a small crown crack in October becomes a major rebuild by March. The risk is real, but we don’t scare-sell. Call (610) 595-5754 and we’ll tell you honestly whether yours can wait.
Written by Russell Haines, Owner, Hearthstone Chimney Co. at Hearthstone Chimney Co., serving Bethlehem and nearby areas.